Abstract
All modern wireless communication technologies are based on electromagnetism. However, electromagnetic signals are readily susceptible to screening and blocking, so their availability cannot be guaranteed in adverse environments. This raises a fundamental question: Can information be transmitted through an unblockable channel? Here, we show that gravity, under physically realistic conditions, offers such a path. We propose and implement a wireless communication protocol in which a broadcaster encodes a binary message by moving a mass, while a receiver detects the resulting gravitational signal with a gravimeter. We validate this scheme experimentally, successfully transmitting a gravitational message a distance of ≈0.7 meters through a brick wall at a rate of 1 bit per minute. These results establish gravity as a viable platform for practically unblockable communication.
INTRODUCTION
Suppose that Alice is confined to a perfectly shielded room: No photons, sound waves, particles, or thermal signals can enter or escape. If Bob is outside the room, then is there any physical mechanism Alice can use to communicate with him? The answer is yes—she can use gravity. Since mass cannot be negative (1, 2), there is no gravitational analog of charge cancelation and hence no way to hide or screen the presence of mass. Moreover, no known material can passively shield or attenuate gravitational fields (3). Thus, if Alice moves a mass within the room, then the local gravitational field at Bob’s location will change, and this effect can be detected using a gravimeter. Alice can therefore communicate with Bob by encoding information in the gravitational field. In the simplest scenario, Alice can generate a binary gravitational signal by moving the mass between two positions (Fig. 1).

Fig. 1. Schematic of gravitational communication.
Alice (inside a perfectly shielded room) can communicate with Bob (outside the room) by moving a mass between two positions 0 and 1 to create a binary change in the local gravitational field. The inset shows a schematic of the gravitational acceleration g measured with Bob’s gravimeter as a function of time t, as Alice moves the mass between the two positions.
This practically unblockable wireless communication scheme stands in contrast to conventional methods based on electromagnetic (EM) waves, as these can be passively blocked by Faraday cages and attenuate when passing through matter (4). Near-unblockable communication has previously been proposed using neutrinos (5) and gravitational waves (6), but these approaches are somewhat hindered by the difficulty in generating a measurable signal—e.g., requiring the manipulation of black holes—as well as the prohibitively large detectors required (5, 7). By contrast, the protocol considered here does not rely on the generation or detection of propagating gravitational waves but, instead, on quasi-static changes in the Newtonian gravitational field produced by controlled motion of a nearby mass. The implementation is therefore straightforward, requiring only a mass and an off-the-shelf, hand-held gravimeter. For example, if Alice has access to a 100-kg mass and moves it from 1 to 2 m away from Bob, then the expected change in gravitational acceleration at Bob’s location is ∼5 nm s−2 (see Eq. 1). While this change may go unnoticed by the casual observer, Bob’s gravimeter is capable of detecting it.
Off-the-shelf gravimeters, typically based on mass-spring (8–10) or falling-corner-cube (11) designs, can provide sensitivities of ∼1 nm s−2 (12). Higher precisions of ∼0.01 nm s−2 can be reached with superconducting gravimeters (12, 13) although at a cost of portability and price. Emerging gravimetry platforms—such as cold-atom interferometry (14, 15), optically levitated nanospheres (16, 17), and microelectromechanical systems devices (18–20)—promise even higher precision or low-cost alternatives in the near future. These advances may unlock a range of previously inaccessible technologies, such as detecting contraband materials (21) and underwater objects (22) or constructing gravimetry networks for early-warning earthquake detection (23). It is therefore an opportune time to consider the possibility of gravitational communication.
Here, we first explore the theoretical properties of gravitational communication, including signal strengths, broadcast directionality, data rates, and robustness. We then experimentally demonstrate this scheme by broadcasting a gravitational message using an elevator counterweight, with an off-the-shelf spring-based gravimeter used for detection.
RESULTS
Signal generation
Our proposed gravitational communication scheme is purely classical and can therefore be described by Newton’s law of gravitation. If Alice holds a point mass M at position , the gravitational acceleration it creates at Bob’s detector (assumed to be at the origin) is
where G is the gravitational constant. As Alice moves her mass between two positions, and , this gravitational acceleration changes by , generating a signal for Bob to measure.
According to Eq. 1, the largest signal that Alice can theoretically generate is , assuming that she is constrained to one side of the sensor (as in Fig. 1) and that she has sufficient space to move the mass from some initial distance to a much greater . However, if Bob’s gravimeter—like many off-the-shelf gravimeters—only measures the vertical component of gravity , then the maximum signal will decrease. In the best case, Alice can still achieve , provided that she is able to move the mass between vertical positions (details of this calculation can be found in the Supplementary Materials). Geometric effects can therefore be largely mitigated but only by displacing the mass over a distance on the order of the transmission length.
In the above, we implicitly assume that (i) Alice and Bob share a fixed inertial reference frame and (ii) Alice’s mass can be moved without appreciably affecting the reference frame. This is an excellent approximation when the frame is anchored to a planet-sized body such as Earth, for which the recoil associated with Alice’s mass displacement is negligible. In a freely floating system such as a spacecraft, however, momentum conservation requires any displacement of Alice’s mass to be accompanied by compensating motion elsewhere in the system, so that the center of mass (COM) remains fixed. This compensation could, in principle, be supplied by thrusters, which eject a small amount of propellant carrying the required momentum. We leave a full treatment of gravitational communication in spacecraft for future work.
Directional properties
By moving the mass between her two chosen positions, Alice has created a gravitational antenna. To understand this antenna’s properties, we consider a point mass moved vertically between and , as illustrated in Fig. 2A, and a single z-axis gravimeter as the detector, located at polar position . Figure 2B shows a series of normalized polar plots of the change in gravitational signal as a function of the gravimeter’s angular position α for multiple radii r (denoted by the legend). For mathematical details, see the Supplementary Materials.

Fig. 2. Gravitational dipole antenna.
(A) Schematic of a point mass moving between vertical positions and . The gravimeter, at position (r, α) in the xz plane, measures a change in gravitational field as the mass moves between the two positions. (B) Polar plots of the vertical signal from the gravitational antenna, as a function of the polar angle α from the axis of the antenna. Line colors denote the radial distance from the center of the antenna, indicated by the legend. The strength of the signal at each radius is normalized to the largest value at that radius. For comparison, an EM half-wave dipole antenna radiation pattern is shown as a black dotted line. Note that all patterns are symmetric with respect to rotation around the z axis.
For , the signal is independent of α, and, hence, the antenna is omnidirectional for an observer near its center. As approaches unity, the signal becomes increasingly directional along the z axis due to the increasing proximity of the gravimeter to the mass at α = 0° and α = 180° (note that the signal diverges at when the two coincide). Further increasing r leads to the far-field regime (), where the antenna’s transmission broadens again but remains primarily directed along its axis.
For comparison, we show the far-field radiation pattern of an EM half-wave dipole antenna (24) (dotted line in Fig. 2B). This looks broadly similar to the gravitational antenna’s far-field signal, except for a rotation by 90° relative to the antenna’s axis. However, the gravitational antenna transmits at 0.25 of its maximum perpendicular to its two lobes in the far field, whereas the dipole EM antenna has zero transmission in the perpendicular directions. Despite the similarities between the radiation patterns, we emphasize that the two physical scenarios are quite different: EM antennas rely on flowing currents to generate EM waves, whereas the quasi-static gravitational antenna creates a change in a static field, more akin to a static electric dipole. Accordingly, the gravitational antenna signal decays with distance as ∼r−3 in the far field (see the Supplementary Materials) compared to the ∼r−1 decay of an EM antenna (4).
Data rate
A key property of any communication channel is the maximum rate of error-correctable data transfer it allows, known as its capacity C. For a noisy digital channel, the Shannon-Hartley theorem (25) gives , with being the bit transmission frequency and SNR being the signal-to-noise ratio. Here, we take , where T is the time it takes Alice to move the mass between positions 0 and 1 and τ is the integration time of Bob’s measurement. Assuming that the noise is Gaussian, the SNR will grow as for sampling frequency . For a gravitational signal from a point mass, the SNR will also decay with distance r as , where is the single-shot SNR at some reference distance . Putting this all together, the channel capacity for binary gravitational communication can be written
(2)
In the regime where the signal is easily resolvable (i.e., ), the logarithmic term varies slowly with both integration time τ and distance r, and, hence, the prefactor dominates the scaling. In this limit, reducing r therefore makes little difference to the channel capacity—it is ultimately limited by T + τ and would be most efficiently increased by reducing these two timescales as much as possible. Conversely, in the limit of near-zero signal, , the channel capacity reduces to . This function is maximized at τ = T, so reducing τ below this value actually leads to a reduction in the channel capacity, despite increasing the bit rate.
Robustness to signal jamming, blocking, and spoofing
While this communication method cannot be passively blocked in the manner of EM shielding, it can, in principle, be affected by active signal degradation strategies. A malicious actor, Mallory, could attempt to jam the signal by moving other nearby masses or generating environmental vibrations, reducing the SNR at Bob’s gravimeter. Mallory could also attempt to locally block (spoof) Alice’s signal by moving a nearby mass so as to counteract (reproduce) the change in gravitational field at Bob’s location. In this case, Bob would observe a modified or misleading signal rather than the one generated by Alice.
In a more elaborate scenario, Mallory could attempt to block the signal entirely by constructing the gravitational analog of a Faraday cage. This would require surrounding either Alice or Bob with a continuous distribution of controllable mass and dynamically reconfiguring it in response to Alice’s motion so as to cancel at all times. Such an arrangement, while not forbidden by physics, would require Mallory to have extraordinary capabilities with regard to control and coordination of mass distributions. We explore this possibility further in the Supplementary Materials.
Experiment
We experimentally demonstrate the proposed method of communication by transmitting a gravitational message through a wall from an elevator shaft into an adjacent room using a movable elevator counterweight. The change in gravitational field is detected at a nearby location with an off-the-shelf sensor. Specifically, we use a LaCoste and Romberg Model D mass-spring gravimeter, which measures relative changes in the vertical component of the gravitational field (26). It has a data acquisition rate of ≈1.9 Hz, digital resolution of 10 nm s−2, and an in-built low-pass filter with a 40-s window for removing high frequency noise. We measure its sensitivity in the experimental location to be ∼2 nm s−2 after 30 s of averaging (see the Supplementary Materials).
We placed the sensor on the ground floor, separated from the counterweight by a brick wall that blocks acoustic, optical, and near-infrared communication (see Fig. 3A). As the counterweight moves vertically, there is a change in the vertical gravitational acceleration at the gravimeter’s location. This change, schematically depicted in Fig. 3B as a function of the counterweight’s vertical position z, allowed us to encode a binary message in the movement of the mass as it transited between the lower and upper floors (as in Fig. 1).

Fig. 3. Schematic of experimental setup.
(A) The counterweight in the lower (0) and upper (1) (dotted boundary) position (not to scale). The force on the gravimeter’s test mass due to the gravitational attraction to the counterweight changes in both magnitude and direction between the two positions, as indicated. (B) Schematic of the expected vertical gravitational signal as a function of the counterweight’s vertical position. The lower and upper counterweight positions are indicated as and , respectively. The maximal vertical signal occurs at an intermediate height , resulting from the tradeoff between the directionality of the sensor and the fall-off of gravity.
To maximize the signal for the demonstration, we placed the gravimeter as close as possible to the counterweight, at horizontal distances m and m from the gravimeter’s center to the counterweight COM. We estimated the counterweight’s COM to be m above the gravimeter in the lower (0) position and m above it in the upper (1) position (see Fig. 3). The COM of the counterweight was therefore a distance of m away from the sensor in its closest position, which we define as the range of the communication scheme. We also estimated the counterweight’s mass to be 1800(200) kg. Materials and Methods contain further details regarding these measurements.
We constructed a model of this setup, approximating the counterweight as a rectangular prism of uniform density. Using an integral form of Newton’s law of gravitation, we calculated the vertical gravitational signal at the location of the sensor as a function of the model counterweight’s vertical position (see schematic in Fig. 3B; further details can be found in Materials and Methods). The model predicts a change in of 50 (15) nm s−2 as the counterweight moves between the upper and lower positions, which we expect to be resolvable with our gravimeter. The model further suggests that a ≈70% signal boost would be achievable by optimizing the counterweight position such that (see Fig. 3B).
We began the experiment by vertically aligning the gravimeter using its built-in spirit levels, followed by ≈20 min of settling time. We then started acquiring data, leaving the elevator counterweight in the lower position for ≈25 min to obtain a background measurement. Following this, we transmitted a gravitational sequence of nine 7-bit ASCII characters by moving the elevator counterweight between its two positions in a chosen sequence. The bits were sent at a rate of 1 per minute, allowing for the ≈25-s counterweight movement time, followed by 10-s settling time and 25 s of integration time. We chose to transmit the word “Gravity”, which is expressed as 49 bits: 1000111 1110010 1100001 1110110 1101001 1110100 1111001. We also included a control sequence of seven alternating bits (1010101) both before and after the message to delineate the signal from the background and establish the transmission bit rate that the receiver should expect. After the bit sequence, we acquired an additional ≈20 min of background (with the counterweight returned to its lower position) to quantify measurement drift (see the Supplementary Materials).
The gravitational signal detected by the gravimeter over the course of the experiment is shown in Fig. 4. Note that these data have been corrected for both Earth tide and sensor drift (the raw data are presented in fig. S5). Each character is delineated with vertical dashed lines, and each bit is delineated with alternating background shading. The horizontal solid lines indicate the mean value measured over that time window. Evidently, the data show distinct shifts of ≈50 nm s−2 each time the elevator counterweight is moved, consistent with the prediction of our model. While there are small fluctuations in the mean values, the averaged 0 and 1 signals are clearly distinguishable, and the detected bit sequence exactly matches the original transmission. For comparison, a dotted horizontal line is shown in Fig. 4 at 25 nm s−2, approximately halfway between the two bit values. Even without averaging, the bit error rate of individual measurements (i.e., the probability of a bit flipping by crossing the threshold) is already ≈0.01. After averaging, this value reduces to ≈10−9 (assuming Gaussian fluctuations), comparable to optical fiber error rates (27). To further validate this result, we confirm that the measurement is insensitive to local magnetic fields, which could, in principle, affect the gravimeter’s steel spring (see the Supplementary Materials). We have thus successfully transmitted and received a message via the gravitational field.

Fig. 4. Experimental gravitational signal.
Gravimetry signal over the transmission sequence (corrected for tide and drift; see the Supplementary Materials). The start and end points of each 7-bit ASCII character are denoted with vertical dashed lines. The 60-s temporal window for each bit is indicated by the alternating blue and white shading, and horizontal solid lines show the corresponding mean for that interval, where the average is taken over the final 25 s. All measurements above (below) gz = 25 nm s−2 (horizontal black dotted line) after correction are recorded as a 1 (0). Note that this is a relative gravitational measurement and, hence, the offsets of the data are arbitrary. The sign convention of the data is such that a positive change in corresponds to an increase in downward acceleration.
Potential improvements
Our experiment achieved a data transfer rate of 1 bit min−1. The channel capacity for our experimental parameters is ≈2.4 bit min−1, so, in principle, improvements could be made to the scheme by implementing more efficient encoding methods, e.g., phase shift keying (28). This optimal information rate is limited by a number of factors, such as the slow movement of the elevator, and the 40-s low-pass filter integrated within the gravimeter. If our building had a modern elevator with a transition time of 5 s and we had access to the latest Scintrex CG-6 gravimeter (29), then the channel capacity would increase to ≈15 bit min−1 [assuming an integration time of 0.1 s for a single sample, with SNR ≈ 5 (30)]. However, improvements beyond this would be challenging with our scheme, given that the mass movement time is the limiting factor.
While the data rate remains modest even after foreseeable improvements, the communication range can, in principle, be increased substantially. The achievable range is set by the magnitude of the field perturbation produced at the receiver relative to the sensitivity and noise floor of the detector. Table 1 lists a number of optimizations that could be made, as well as their expected improvement factor for the range, based on Eq. 1. First, the configuration could be modified by compressing the mass into a more spatially localized geometry (ideally, a sphere) and vertically aligning it with the gravimeter. These changes would increase the signal by a factor of ≈4.9 at the same distance of ≈0.7 m. The mass itself could be increased within reason to, e.g., 7.5 × 104 kg [equivalent to a typical military tank (31)]. An order of magnitude of SNR could also be sacrificed in favor of range, and, in principle, a higher sensitivity gravimeter could be used [e.g., a superconducting device (12, 13) or potentially a future cold atom interferometer (32, 33)]. Our experimental model predicts that compromising SNR (the only option available with our current setup) could increase the potential range to ≈1.7 m. Combining all the improvements listed in Table 1, we predict that the range could be increased by a factor of ∼700 to ∼500 m.
| Current | Potential | Range increase factor | |
|---|---|---|---|
| Geometric factor | 1 | ≈4.9 | ≈2.2 |
| Mass (kg) | 1800 | 75,000 | ≈6.5 |
| Sensitivity (nm s−2) | ≈2 | ≈0.01 | ≈14 |
| SNR | ≈25 | ≈2 | ≈3.5 |
Even with these idealized improvements, the scheme has a low data rate and short range when compared to other use cases. For example, the transmission rate for uplink commands to the Voyager 1 spacecraft—the furthest human-made object from Earth at ∼1013 m away—is an appreciably higher ≈960 bit min−1 (34) (although being EM, this signal is inherently susceptible to jamming and blocking). We therefore expect gravitational communication to be best suited to the transmission of concise messages over relatively short distances in challenging or constrained environments.
DISCUSSION
We have proposed a form of practically unblockable communication using classical gravitation and performed a proof-of-principle experimental demonstration. Using an elevator counterweight and an off-the-shelf gravimeter, we have successfully transmitted a gravitational message.
Although this technology is restricted to relatively short-range, low bit-rate applications, its distinct advantages may be relevant for some niche use cases. Since it is possible to measure gravitational fields without the need for electronics (26, 35) (akin to semaphore), this approach could be made radiation proof; however, unlike semaphore, it is not limited by line of sight.
A scheme similar to that demonstrated here would be well suited to communication from within secure facilities in a covert manner, which could be considered to prevent data leaks. There may also be applications in wireless communication to or from sealed nuclear bunkers. More broadly, this work demonstrates that gravity itself can serve as a carrier of information, albeit with limited bandwidth and range. Should the reader ever experience prolonged entrapment in a soundproofed, Faraday-caged elevator with a malfunctioning phone, the present method offers an experimentally verified means of signaling for aid.
MATERIALS AND METHODS
Analytical model
We construct a model of the experimental configuration to estimate the gravitational signal we expect to observe at the location of the gravimeter. The counterweight is approximated to be a three-dimensional rectangular prism of uniform of density kg m−3 and volume , with m, m, and m. We position its COM at m and m and allow it to move along the vertical (z) axis (see the next section for details on how these measurements have been obtained). At each vertical position, we calculate the gravitational field by integrating Newton’s law of gravitation over the density distribution
(3)
where is the region containing nonzero density and is the location of the sensor. For a rectangular prism of fixed density ρ contained within the region , , , the resulting expression for can be written analytically as (36)
(4)
The x component of can be written
(5)
where , , , and . The y (z) component of can then be obtained by permuting , , and once (twice).
Figure 5 shows the vertical gravitational signal obtained from the model (solid blue line), with uncertainty indicated by the shading. At large distances, the vertical gravitational force is weak but increases as the counterweight moves downward. However, past the peak at ≈0.8 m (identified with a circle), the signal starts to drop toward zero, as the gravitational field becomes predominantly along the x axis. This peak corresponds to the optimal position (see the Supplementary Materials). In Fig. 5, we also show the signal predicted for a point mass with the same total mass as the counterweight, located at the position of its COM (dotted line). As expected, the two curves agree in the far field, where the distributed density begins to look point-like. However, when the counterweight is closer to the sensor, the point mass curve produces a much stronger signal, and the optimal position shifts to m. This highlights the benefits that could be realized if the mass was made denser (e.g., compacted into a sphere).

Fig. 5. Model of counterweight gravitational signal.
Analytical model of the vertical gravitational acceleration due to the counterweight (blue solid line) as a function of the z-position of its COM relative to the gravimeter. Shading around the curve denotes one standard deviation error arising from the uncertainty in the counterweight size and density, as well as the distance to the sensor. Vertical lines indicate and , the lower and upper positions of the counterweight, respectively. The shaded regions show one standard deviation error in these positions. A point mass approximation of the signal is also shown (red dotted line). The maximal signal, corresponding to the position , is indicated on each line with a circle.
The experimental values for the lower and upper positions of the counterweight ( and , respectively) are indicated in Fig. 5 with vertical lines (shading denotes the uncertainty in these values). (Details regarding how these positions have been obtained are presented in the following section.) According to the distributed counterweight model, the expected signals at each location are 54(15) nm s−2 (lower) and 3.6(3) nm s−2 (upper), giving a difference of nm s−2. This value agrees well with the experimentally observed signal of ≈50 nm s−2 .
Estimation of counterweight geometry and mass
To determine the counterweight COM z position relative to the gravimeter in its lower position in the experiment, we used a laser distance meter (LDM) and purpose-built pendulum theodolite, mounted to a tripod (see left side of Fig. 6). The pendulum theodolite consisted of a fishing line with a mass on the end, attached to the center of a protractor. A laser pointer was also mounted along the edge of the protractor, directed along the 0 to 180° line. The theodolite was first aligned such that the laser pointed to the top of the counterweight (solid red line in Fig. 6), before being rotated until the laser reached the bottom of the counterweight (dashed red line). As it was rotated, the pendulum remained vertical due to the Earth’s gravity, allowing a measurement of the angles α1 and α2 relative to this fixed reference (see Fig. 6). We then attached the LDM to the center of the theodolite, enabling us to measure the distance from this point to the top of the counterweight (the LDM could not provide a reliable measurement of the distance to the bottom of the counterweight due to poor reflectance). Using these measurements, as well as the measured height of the theodolite, trigonometry was used to determine the counterweight’s vertical length, m. The counterweight’s center point (assumed to be its COM) was also estimated from this method to be at a vertical position m above the gravimeter (see Fig. 6). Building plans informed us that the elevator moves a distance of 5.41 m between the upper and lower levels and, hence, the upper position of the counterweight was estimated to be m.

Fig. 6. Estimation of counterweight geometry.
Schematic diagram of the experimental setup and measurement scheme for the elevator counterweight dimensions while in the lower position (not to scale). The left side shows the combined LDM and theodolite, used for measuring the angle α1 (α2) to the top (bottom) of the counterweight, as well as the distance ( could not be measured; see text). The counterweight height and vertical position obtained using this method are indicated, as well as the horizontal depth and distance to the gravimeter .
The depth and width could not be estimated using this method due to a lack of absolute horizontal reference. Fortuitously, shortly after completing the experiment, a technician performing an elevator service was kind enough to provide us with measurements of m and m.
To obtain the horizontal distance between the counterweight and the gravimeter, we needed an estimate of the wall thickness (the technician also provided a measurement of the distance between the counterweight and the wall). To this end, we conducted a survey with a tape measure and the LDM from our reference point at the front of the elevator shaft to the gravimeter, via a hallway next to the elevator shaft. This gave a wall thickness of 0.27(2) m, consistent with a nearby wall in the same building that we could measure directly. We therefore estimated the total separation to be m.
Last, from the counterweight’s measured dimensions, we estimated its mass to be 1800(200) kg, assuming a uniform density of 7300(200) kg m−3. This density is typical of gray cast iron—the material of choice for mid 20th-century lift counterweights.
Acknowledgments
We thank Geoscience Australia for the loan of the gravimeter and for technical advice, as well as G. Gauthier, C. Thomson, L. Williamson, and S. Haine for comments on the manuscript. A.G.W. wishes to thank P. Nussenzveig for conversations musing on applications of next-generation quantum technologies. Last, we thank the reviewers for their constructive feedback, which improved the manuscript.
Funding:
A.J.G., C.W.W., A.G.W., and M.J.D. were funded by the Australian Research Council Centre of Excellence for Engineered Quantum Systems (EQUS, CE170100009). A.J.G., M.J.D., and A.G.W. were also funded by the Australian government Department of Industry, Science, and Resources via the Australia-India Strategic Research Fund (AIRXIV000025). A.G.W. is the recipient of an Australian Research Council Laureate Fellowship (FL210100045) funded by the Australian government.
Author contributions:
Conceptualization: C.W.W., M.D.H., A.J.G., A.G.W., and M.J.D. Formal analysis: C.W.W., M.D.H., A.J.G., A.G.W., and M.J.D. Investigation: C.W.W., M.D.H., A.J.G., A.G.W., and M.J.D. Methodology: C.W.W., M.D.H., A.J.G., A.G.W., and M.J.D. Supervision: M.J.D. Writing—original draft: C.W.W., M.D.H., A.J.G., A.G.W., and M.J.D.
Competing interests:
The authors declare that they have no competing interests.
Data, code, and materials availability:
All data and code needed to evaluate and reproduce the results in the paper are available at the University of Queensland eSpace data repository, https://doi.org/10.48610/cd26dd2. This study did not generate new materials.
Supplementary Materials
This PDF file includes:
Supplementary Text
Figs. S1 to S6
References
REFERENCES
1
R. Schoen, S.-T. Yau, On the proof of the positive mass conjecture in general relativity. Commun. Math. Phys. 65, 45–76 (1979).
2
N. de Aguiar Alves, A. G. S. Landulfo, B. A. Costa, Positive mass in general relativity without energy conditions. Phys. Rev. D 111, 044027 (2025).
3
C. S. Unnikrishnan, G. T. Gillies, New limits on the gravitational Majorana screening from the Zürich G experiment. Phys. Rev. D 61, 101101 (2000).
4
D. J. Griffiths, Introduction to Electrodynamics (Cambridge Univ. Press, 2023).
5
D. D. Stancil, P. Adamson, M. Alania, L. Aliaga, M. Andrews, C. A. Del Castillo, L. Bagby, J. L. Bazo Alba, A. Bodek, D. Boehnlein, R. Bradford, W. K. Brooks, H. Budd, A. Butkevich, D. A. M. Caicedo, D. P. Capista, C. M. Castromonte, A. Chamorro, E. Charlton, M. E. Christy, J. Chvojka, P. D. Conrow, I. Danko, M. Day, J. Devan, J. M. Downey, S. A. Dytman, B. Eberly, J. R. Fein, J. Felix, L. Fields, G. A. Fiorentini, A. M. Gago, H. Gallagher, R. Gran, J. Grange, J. Griffin, T. Griffin, E. Hahn, D. A. Harris, A. Higuera, J. A. Hobbs, C. M. Hoffman, B. L. Hughes, K. Hurtado, A. Judd, T. Kafka, K. Kephart, J. Kilmer, M. Kordosky, S. A. Kulagin, V. A. Kuznetsov, M. Lanari, T. Le, H. Lee, L. Loiacono, G. Maggi, E. Maher, S. Manly, W. A. Mann, C. M. Marshall, K. S. Mcfarland, A. Mislivec, A. M. Mcgowan, J. G. Morfín, H. Da Motta, J. Mousseau, J. K. Nelson, J. A. Niemiec-Gielata, N. Ochoa, B. Osmanov, J. Osta, J. L. Palomino, J. S. Paradis, V. Paolone, J. Park, C. Peña, G. Perdue, C. E. Pérez Lara, A. M. Peterman, A. Pla-Dalmau, B. Pollock, F. Prokoshin, R. D. Ransome, H. Ray, M. Reyhan, P. Rubinov, D. Ruggiero, O. S. Sands, H. Schellman, D. W. Schmitz, E. C. Schulte, C. Simon, C. J. Solano Salinas, R. Stefanski, R. G. Stevens, N. Tagg, V. Takhistov, B. G. Tice, R. N. Tilden, J. P. Velásquez, I. Vergalosova, J. Voirin, J. Walding, B. J. Walker, T. Walton, J. Wolcott, T. P. Wytock, G. Zavala, D. Zhang, L. Y. Zhu, B. P. Ziemer, Demonstration of communication using neutrinos. Modern Phys. Lett. A 27, 1250077 (2012).
6
H. Wang, O. B. Akan, Gravitational communication: Fundamentals, state-of-the-art, and future vision. IEEE Commun. Surv. Tutor. 28, 3564–3595 (2026).
7
LIGO Scientific Collaboration and Virgo Collaboration, Observation of gravitational waves from a binary black hole merger. Phys. Rev. Lett. 116, 061102 (2016).
8
J. M. Goodkind, The superconducting gravimeter. Rev. Sci. Instrum. 70, 4131–4152 (1999).
9
M. Van Camp, O. de Viron, A. Watlet, B. Meurers, O. Francis, C. Caudron, Geophysics from terrestrial time-variable gravity measurements. Rev. Geophys. 55, 938–992 (2017).
10
S. K. Haldar, Mineral Exploration (Elsevier, ed. 2, 2018).
11
T. Niebauer, “3.03—Gravimetric methods—Absolute gravimeter: Instruments concepts and implementation,” in Treatise on Geophysics, G. Schubert, Ed. (Elsevier, 2007), pp. 43–64.
12
W. Freeden, Gravimetry (Springer International Publishing, 2021), pp. 41–48.
13
H. Virtanen, “Studies of Earth dynamics with the superconducting gravimeter,” thesis, University of Helsinki, Finland (2006).
14
M. Kasevich, S. Chu, Measurement of the gravitational acceleration of an atom with a light-pulse atom interferometer. Appl. Phys. B 54, 321–332 (1992).
15
X. Wu, Z. Pagel, B. S. Malek, T. H. Nguyen, F. Zi, D. S. Scheirer, H. Müller, Gravity surveys using a mobile atom interferometer. Sci. Adv. 5, eaax0800 (2019).
16
F. Monteiro, W. Li, G. Afek, C.-L. Li, M. Mossman, D. C. Moore, Force and acceleration sensing with optically levitated nanogram masses at microkelvin temperatures. Phys. Rev. A 101, 053835 (2020).
17
T. Liang, S. Zhu, P. He, Z. Chen, Y. Wang, C. Li, Z. Fu, X. Gao, X. Chen, N. Li, Q. Zhu, H. Hu, Yoctonewton force detection based on optically levitated oscillator. Fundam. Res. 3, 57–62 (2023).
18
R. P. Middlemiss, A. Samarelli, D. J. Paul, J. Hough, S. Rowan, G. D. Hammond, J. T. Wright, Measurement of the Earth tides with a MEMS gravimeter. Nature 531, 614–617 (2016).
19
S. Tang, H. Liu, S. Yan, X. Xu, W. Wu, J. Fan, J. Liu, C. Hu, L. Tu, A high-sensitivity MEMS gravimeter with a large dynamic range. Microsyst. Nanoeng. 5, 45 (2019).
20
A. Mustafazade, M. Pandit, C. Zhao, G. Sobreviela, Z. Du, P. Steinmann, X. Zou, R. T. Howe, A. A. Seshia, A vibrating beam MEMS accelerometer for gravity and seismic measurements. Sci. Rep. 10, 10415 (2020).
21
B. Kirkendall, Y. Li, D. Oldenburg, Imaging cargo containers using gravity gradiometry. IEEE Trans. Geosci. Remote Sens. 45, 1786–1797 (2007).
22
L. Wu, J. Tian, Automated gravity gradient tensor inversion for underwater object detection. J. Geophys. Eng. 7, 410–416 (2010).
23
Y.-W. Kwon, J.-K. Ahn, J. Lee, C.-H. Lee, “Earthquake early warning using low-cost MEMS sensors,” in IGARSS 2020–2020 IEEE International Geoscience and Remote Sensing Symposium (IEEE, 2020), pp. 6635–6637.
24
S. Ramo, J. Whinnery, T. Van Duzer, Fields and Waves in Communication Electronics (Wiley, 1994).
25
C. E. Shannon, A mathematical theory of communication. Bell Syst. Tech. J. 27, 379–423 (1948).
26
LaCoste and Romberg, Instruction Manual: Model G and D Gravity Meters (LaCoste and Romberg, 1997).
27
J. Senior, M. Jamro, Optical Fiber Communications: Principles and Practice (Pearson Education, ed. 3, 2009).
28
P. Massoud Salehi, J. Proakis, Digital Communications (McGraw-Hill Education, 5th ed. 2008).
29
Scintrex, CG-6 AutogravTM Gravity Meter Operation Manual (Scintrex, 2018).
30
O. Francis, Performance assessment of the relative gravimeter Scintrex CG-6. J. Geodyn. 95, 116 (2021).
32
S.-W. Chiow, T. Kovachy, H.-C. Chien, M. A. Kasevich, 102ℏk large area atom interferometers. Phys. Rev. Lett. 107, 130403 (2011).
33
A. HosseiniArani, M. Schilling, Q. Beaufils, A. Knabe, B. Tennstedt, A. Kupriyanov, S. Schön, F. Pereira dos Santos, J. Müller, Advances in atom interferometry and their impacts on the performance of quantum accelerometers on-board future satellite gravity missions. Adv. Space Res. 74, 3186–3200 (2024).
35
H. Kater, An account of experiments for determining the length of the pendulum vibrating seconds in the latitude of London. Philos. Trans. R. Soc. Lond. 108, 33–102 (1818).
36
X. Li, M. Chouteau, Three-dimensional gravity modeling in all space. Surv. Geophys. 19, 339–368 (1998).
37
I. M. Longman, Formulas for computing the tidal accelerations due to the moon and the sun. J. Geophys. Res. 64, 2351–2355 (1959).