-
Detailed Specifications
-
Connectors on the KiteBoard
Dimensions
50 mm x 70 mm x 5 mm (without connectors & switches)
50 mm x 70 mm x 8 mm (with connectors & switches)
Application Processor
Quad Core 64 bit ARM Cortex A53 @ 1.2 GHz
Modem
Integrated Modem with Cat 4 LTE support, 3G/2G fallbacks. Dual SIM support (DSDS). Supports voice, data & SMS.
LTE Bands
-
1,2,4,5,8,13,17 (North America)
-
1,2,3,4,5,7,8,20 (Europe hardware)
Operating System
Android L (5.1.1)
System Memory
1 GB LPDDR3 533 MHz (upgradable to 2GB)
Storage
16 GB in-build storage (eMMC)
Additional Storage
Micro SD Card, SD 3.0 (UHS-I)
Wireless Connectivity
WiFi b/g/n, BT 4.1, BT LE 4.0. User selectable Bluetooth power mode (Class 1/Class 2)
GNSS
Qualcomm iZat Gen 8C with support for GPS/GLONASS/Beidou,AGPS support
Audio
Speaker (2W, 8 Ohm), Primary+Secondary Mic, Earpiece, I2S
Sensors
9 axis accelerometer, ecompass, gyroscope
System Power
DC, LiPoly Battery, USB
Battery
3.7/3.8V LiPoly Batteries
Battery Charger
Integrated high current (2A) charger for LiPoly battery supporting Qualcomm QuickCharge 2.0
Camera
4 lane MIPI CSI (rear) camera supporting upto 13 MP camera, with Autofocus support
1 lane MIPI CSI (front) camera supporting upto 5 MP camera
Display
4 lane MIPI DSI interface supporting a maximum resolution of 1080p @ 60Hz
Wireless Display (Miracast) upto 720p @ 30Hz
USB
Single USB 2.0 OTG port
GPIOs
15 GPIOs (9 with platform wake-up capability)
Low speed interfaces
Multiplexed UART (upto 2), SPI (upto 4), I2C (Upto 4) interfaces. Unused pins can be used as additional GPIOs
Miscellaneous
FM Radio Receiver
Buttons
Power (Button)
Volume Up & Down (Pads)
Haptic Feedback
Vibrator Motor (Pads)
| CONNECTOR |
CONNECTOR TYPE |
SIGNALS |
OPTIONAL/INCLUDED |
| USB |
USB Micro B |
USB 2.0 |
Optional |
| DC Input |
|
DC Power, GND |
Optional |
| SIM |
Micro SIM |
SIM 1 |
Optional |
| SD |
Micro SD |
SD Card |
Optional |
| Expansion |
120 pin board to board connector,
4mm stacking height |
GPIOs,UART/I2C/SPI,
system power, SD,
SIM1 & 2, USB,
Audio signals, Buttons |
Included |
| Primary Camera |
30 pin FPC |
4 lane MIPI CSI,
autofocus, power, CCI |
Included |
| Secondary Camera |
24 pin FPC |
1 lane MIPI CSI,
power, CCI |
Included |
| Display |
30 pin FPC |
4 lane MIPI DSI, I2C,
I2S, PWM, Power,
Extra GPIOs |
Included |
| LTE Primary Antenna Connector |
IPX |
|
Included |
| LTE Diversity Antenna Connector |
IPX |
|
Included |
| WiFi/BT Antenna Connector |
IPX |
|
Included |
| GPS Antenna Connector |
IPX |
|
Included |
| Battery |
|
Power, GND, Thermal sense, I2C |
Optional |
The Display connector supports MIPI displays. The display connectors includes an I2C interface, which can be used to directly interface a touch panel. A backlight PWM pin, power & GPIO signals are provided to make it possible to directly interface common MIPI displays panels with integrated touch. Interfacing LVDS/RGB/HDMI displays requires usage of a bridge chip and circuitry to convert the signals. I2S signals are also routed to the display connector – this can be used to implement HDMI audio if required.
USB Micro B, DC Input, MicroSIM, and MicroSD connectors are mounted in development boards. They are, however, optional in production boards. The signals on these connectors are routed to the expansion connector as well – this allows placement of the connectors at an appropriate place, as required in the target application.
-
Detailed Specifications
Dimensions
50 mm x 70 mm x 5 mm (without connectors & switches)
50 mm x 70 mm x 8 mm (with connectors & switches)
Application Processor
Quad Core 64 bit ARM Cortex A53 @ 1.2 GHz
Modem
Integrated Modem with Cat 4 LTE support, 3G/2G fallbacks. Dual SIM support (DSDS). Supports voice, data & SMS.
LTE Bands
-
1,2,4,5,8,13,17 (North America)
-
1,2,3,4,5,7,8,20 (Europe hardware)
Operating System
Android L (5.1.1)
System Memory
1 GB LPDDR3 533 MHz (upgradable to 2GB)
Storage
16 GB in-build storage (eMMC)
Additional Storage
Micro SD Card, SD 3.0 (UHS-I)
Wireless Connectivity
WiFi b/g/n, BT 4.1, BT LE 4.0. User selectable Bluetooth power mode (Class 1/Class 2)
GNSS
Qualcomm iZat Gen 8C with support for GPS/GLONASS/Beidou,AGPS support
Audio
Speaker (2W, 8 Ohm), Primary+Secondary Mic, Earpiece, I2S
Sensors
9 axis accelerometer, ecompass, gyroscope
System Power
DC, LiPoly Battery, USB
Battery
3.7/3.8V LiPoly Batteries
Battery Charger
Integrated high current (2A) charger for LiPoly battery supporting Qualcomm QuickCharge 2.0
Camera
4 lane MIPI CSI (rear) camera supporting upto 13 MP camera, with Autofocus support
1 lane MIPI CSI (front) camera supporting upto 5 MP camera
Display
4 lane MIPI DSI interface supporting a maximum resolution of 1080p @ 60Hz
Wireless Display (Miracast) upto 720p @ 30Hz
USB
Single USB 2.0 OTG port
GPIOs
15 GPIOs (9 with platform wake-up capability)
Low speed interfaces
Multiplexed UART (upto 2), SPI (upto 4), I2C (Upto 4) interfaces. Unused pins can be used as additional GPIOs
Miscellaneous
FM Radio Receiver
Buttons
Power (Button)
Volume Up & Down (Pads)
Haptic Feedback
Vibrator Motor (Pads)
-
Connectors on the KiteBoard
| CONNECTOR |
CONNECTOR TYPE |
SIGNALS |
OPTIONAL/INCLUDED |
| USB |
USB Micro B |
USB 2.0 |
Optional |
| DC Input |
|
DC Power, GND |
Optional |
| SIM |
Micro SIM |
SIM 1 |
Optional |
| SD |
Micro SD |
SD Card |
Optional |
| Expansion |
120 pin board to board connector,
4mm stacking height |
GPIOs,UART/I2C/SPI,
system power, SD,
SIM1 & 2, USB,
Audio signals, Buttons |
Included |
| Primary Camera |
30 pin FPC |
4 lane MIPI CSI,
autofocus, power, CCI |
Included |
| Secondary Camera |
24 pin FPC |
1 lane MIPI CSI,
power, CCI |
Included |
| Display |
30 pin FPC |
4 lane MIPI DSI, I2C,
I2S, PWM, Power,
Extra GPIOs |
Included |
| LTE Primary Antenna Connector |
IPX |
|
Included |
| LTE Diversity Antenna Connector |
IPX |
|
Included |
| WiFi/BT Antenna Connector |
IPX |
|
Included |
| GPS Antenna Connector |
IPX |
|
Included |
| Battery |
|
Power, GND, Thermal sense, I2C |
Optional |
The Display connector supports MIPI displays. The display connectors includes an I2C interface, which can be used to directly interface a touch panel. A backlight PWM pin, power & GPIO signals are provided to make it possible to directly interface common MIPI displays panels with integrated touch. Interfacing LVDS/RGB/HDMI displays requires usage of a bridge chip and circuitry to convert the signals. I2S signals are also routed to the display connector – this can be used to implement HDMI audio if required.
USB Micro B, DC Input, MicroSIM, and MicroSD connectors are mounted in development boards. They are, however, optional in production boards. The signals on these connectors are routed to the expansion connector as well – this allows placement of the connectors at an appropriate place, as required in the target application.
